Tech Library
CAPA History
Dyno Charts
Price List
S.C. Rebuilds
Products by Vehicle

 2018 Mustang V8

 15-17 Mustang V8


 Camaro LT1
 More Vehicles..


 Supercharger Kits

 Supercharger Head Units

 Supercharger Kit Parts

 Supercharger Rebuilds
 and Repairs


 Fuel Systems

 Engine Management

 Holden Power Parts

 Ford Power Parts

 Exhaust Systems

 Clothing & Merchandise


 Chevrolet / GM


 Ford - USA

 Chrysler / Dodge




Home > Supercharger Kits > Chrysler / Dodge Supercharger Kits > Big Block 440 Mopar Carby Paxton Kits

Chrysler/ Dodge Supercharger Kits

Big Block 440 Mopar Carby Paxton Supercharger Kits

These are universal supercharger kits designed for vehicles equipped with carburetted big block Dodge 440 RB engines. Supplied pulley ratio will produce approximately 5-6 psi at 6000 RPM on a lightly modified 440CI engine. Horsepower gains (depending on boost levels, engine volumetric efficiency etc.): 30-75%+.

Designed for OEM Dodge Twin V-Groove Accessory Crank Pulley

The supplied crank pulley is designed to work with the OEM Dodge twin V-groove accessory crank pulley. For correct belt alignment, the proper accessory drive crank pulley must be used.

Fuel Pump and 4150 Carburettor Required

This universal system requires the installer to source a high volume fuel pump and a properly jetted 4150 style carburettor unit (with mechanical secondaries). Vehicle throttle cable/arm modifications may be required. A replacement hood or hood modifications may be required depending upon the type of intake manifold and carburettor enclosure / bonnet installed on the engine.

Included Components
  • Novi 1500 Supercharger (CW rotation; curved discharge) with 10-rib 3.875" diameter pulley
  • Twin billet aluminum mounting plates for rigid supercharger attachment with all necessary hardware
    • Integrated manual belt tensioner with dual bearing billet aluminum idler
    • OEM alternator mounting provisions
  • Supercharger drive assembly:
    • Billet aluminum supercharger crank pulley with hard anodize finish (6" diameter)
    • 10-rib drive belt, spacer and all necessary hardware
  • Supercharger oil drain assembly
  • Supercharger oil feed assembly
  • 4" aluminum inlet ducting with silicone sleeves, stainless clamps and cone-type high-flow filter
  • 3.5" aluminum discharge tube with silicone sleeves and stainless clamps
  • Aluminum race bypass valve with tube and mounting flange (not included in 1201860-1 / 1201860-1P tuner kits). Note: supplied compressor bypass valve installation requires welding in installer specified location
  • Cast aluminum carburettor hat / bonnet (not included in 1201860-1 / 1201860-1P tuner kits). Note: requires properly prepared 4150 Holley or Demon Carburetor modified for use in “blow-thru” applications
Installation time

4-10 hours depending on application

Optional Components

The following is a list of parts that are not included, but may be required for complete system operation:

  • Properly prepared Holley 4150 series 4 barrel carburettor with mechanical secondaries or Demon carburettor (may require re-jetting/minor modification)
  • High-performance fuel pump and fuel pressure regulator (boost referenced)
  • Accessory v-belts (will vary per application depending on accessory configuration and supercharger pulley diameters)
  • Supercharger pulleys: contact technical department for proper application match
    • Paxton # 4MA031-312: 3.12" diameter 10 rib driven pulley
    • Paxton # 4MA031-333: 3.33" diameter 10 rib driven pulley
    • Paxton # 4MA031-347: 3.47" diameter 10 rib driven pulley
    • Paxton # 4MA031-360: 3.60" diameter 10 rib driven pulley
    • Paxton # 4MA018-051: 7.00" diameter 10 rib drive (crank) pulley
    • Paxton # 4MA018-061: 7.80" diameter 10 rib drive (crank) pulley
  • Compressor bypass valve and flange (for higher boost applications)
    • Paxton # 8D103-001 Mondo bypass valve
    • Paxton # 8D003-052 Mondo bypass weld-on flange (aluminum)
    • Paxton # 8D205-003 BV57 bypass valve
    • Paxton # 8D005-051 BV57 bypass weld-on flange (aluminum)
  • Aftermarket ignition amplifier (not required, but recommended)
    • Paxton # 5A001-008 Crane HI-6 ignition amplifier box w/ rev-limiter

Part  Descripton  Boost  Power  Retail
Number        (FW)  (Inc. GST)
Universal Big Block Mopar Carburetted Kit, Novi 1500, Satin $POA
Universal Big Block Mopar Carburetted Kit, Novi 1500, Satin **TUNER KIT** $POA
NOTE: Other Parts Required for a Complete Installation Eg Fuel Lines, Ignition Components  
NOTE: Tuner Kits Require Carby Hat/Enclosure, Discharge Pipework, Bypass Valve, Fuel Components and Ignition Components for a complete installation  
NOTE: Polished Kits Also Available  

 © 2018 CAPA Performance